DGCA AME CAR 66 MODULE 7 Main Maintenance Exam Question Paper
Q.1) The horizontal distance that piece or part of an aircraft is located from datum is [Module 7,16.3]
a) Arm
b) Moment
c) Centre of gravity
Q.2) The imaginary straight line from L.E. to T.E. is [Module 7,16.26]
a) Camber
b) Chord
c) Mean aerodynamic chord
Q.3) MTCS [Old 9A]
a) Heavy mass at smaller distance is equal to light mass at smaller distance
b) Heavy mass at longer distance is equal to light mass at smaller distance
c) Heavy mass at smaller distance is equal to light mass at smaller distance
d) Heavy mas at smaller distance is equal to light mass at longer distance
Q.4) What should be slackness of flexible hose [9A,7.19]
a) 3% to 8%
b) 5% to 8%
c) 5% to 10%
Q.5) Maximum zero fuel weight is [Module 7,16.5]
a) Heaviest weight an aircraft can be loaded without usable fuel
b) Heaviest weight an aircraft can be loaded without fuel, oil, and hydraulic
c) Heaviest weight an aircraft can be loaded without unusable fuel
Q.6) Troubleshooting involves [Module 7,5.13]
a) Schematic drawing
b) Installation drawing
c) Wiring diagram
Q.7) Useful load is [Module 7,16.5]
a) MTOW – Maximum landing weight
b) Maximum allowable grows weight – empty weight
c) Maximum allowable grows weight – zero fuel weight
Q.8) MTCS, type of torque wrenches [Module 7,3.15]
a) Beam, rigid beam, micrometre
b) Flexible beam, rigid frame, dial indictor, micrometre
Q.9) MTCS, Helicopter [Module 7,1.13]
a) Approach helicopter not in view of pilot
b) Approach single rotor helicopter from rear
c) Never approach single rotor helicopter from rear
d) Never approach helicopter in view of pilot
Q.10) Best precaution for seaplanes in stormy atmosphere [Module 7,17.2]
a) Tie down & secure To anchor
b) Loose all the ropes
c) Install control lock
Q.12) In which welding non-consumable electrode is used [Module 7,15.8]
a) Electrode arc welding
b) TIG welding
c) Spot welding
Q.13) MTCS, Brazing inspection [Module 7,15.4]
a) Solder is distributed evenly throughout the gap
b) There should be gap between filling gap
c) Excess flux should not be removed
Q.14) Bismuth & cadmium are added to [Shop Theory]
a) To lower the melting point
b) To increase the melting point
c) Doesn’t affect the melting point
Q.15) Soldering flux, MTCS [Module 7,15.2]
a) Clean the area to remove oxide
b) So as to prevent corrosion
c) Also prevent oxide formation
d) All
Q.16) Minimum bend allow in RF cable [Module 7,7.21]
a) 6 times the O.D.
b) 10 times the O.D.
c) 3 times the O.D.
Q.17) MTCS, hacksaw [Module 7,3.19]
a) Cuts only in one direction
b) Cuts in both direction
c) Cuts only in return direction
d) Do not cut in forward stroke
Q.18) Hacksaw teeth has [Module 7,3.19]
a) 10-12 TPI
b) 12-30 TPI
c) 30-50 TPI
d) 14-32 TPI
Q.19) Type of spring that is heat treated often forming
a) Annealed sheet spring
b) Belleville spring
Q.20) When spring gets overheated [Module 7,10.2]
a) Its looses it temper
b) Its colour changes
c) Its load caring capacity detoriates
d) All
Q.21) 150 offset, used for turning in check nut wrench for [Shop Theory,48]
a) Check nut or jam nut
b) Castelled shear nut
c) Castelled nut only
Q.22) Cable guides
a) Fairlead
b) Pully
c) Pressure Seals
d) All
Q.23) Specific gravity is measured by [Module 7,,16.12]
a) Hydrometer
b) Hygrometer
c) Both
d) None
Q.24) Corrosion along grain boundaries [Module 7,,18.13]
a) Fretting corrosion
b) Intergranular corrosion
c) Galvanic corrosion
Q.25) Corrosion due to improper heat treatment [Module 7,18.13]
a) Galvanic corrosion
b) Intergranular corrosion
c) None
Q.26) De-icer boots are [Module 11,12.25]
a) Impregnated by conductive cement
b) Impregnated by neoprene rubber
c) Zinc oxide coated
Q.27) MTCS, rigid tube installation [Module 7,9.8]
a) Never apply compound to the faces of fitting
b) Apply compound of faces of fitting
c) Pipe lines should be 15% larger than required
Q.28) Transport category load factor [CAR,F part III]
a) +2.5G to +3.8G / -1G to -1.5G
b) +4.5G to +6G / -1.7G to -3G
c) +2.5G to +3.8G / -1.76G to -3G
Q.29) Which of the following are cable fitting [9A,5.78]
a) Terminals
b) Bushings
c) Sheklas
d) All
Q.30) Repair, MTCS
a) Very early & convenient
b) Involves a great deal of labour
c) Complex works takes less fine
Q.31) AN 380 [Module 6,5.20]
a) Cd plated low carbon steel
b) CRS
c) Cd plated high carbon steel
Q.32) False brinelling is [Module 6,4.8]
a) Fretting corrosion
b) Intergranular corrosion
c) Stress corrosion
Q.33) Human factor is designed for
a) System +Airline
b) People + system
c) People + hanger
Q.34) wing rigging checks [15A,2.51-2.53]
a) Symmetry
b) Dihedral
c) Incidence
d) All
Q.35) Which line is composed of one long and two short dashes [Module7,5.17]
a) Hidden line
b) Phantom line
c) Extension line
d) Stich line
Q.36) Corrosion removal [Module 7,18.9]
a) Cleaning of A/C corroded parts
b) Appling M.E.K. on corroded parts
c) Appling ATF on corroded parts
Q.37) Which of the following is called DASH line [Module 7,5.19]
a) Hidden line
b) Stich line
c) Phantom line
Q.38) Arrow head line are called [Module 7,5.19]
a) Extension line
b) Leader line
c) Phantom line
Q.39) Isometric project [CAIP I-4,8]
a) 45 degree at place of projection
b) 60degree at place of projection
c) 30 degree at place of projection
Q.40) Datum is [Module 7,16.3]
a) Horizontal plane where all horizontal measurements are takes
b) Vertical plane where all vertical measurements are takes
c) Horizontal plane where all vertical measurements are takes
d) Vertical plane where all horizontal measurements are takes
Q.41) MTCS, corrosion [Module 7,18.13]
a) Mg is anodic to all do not use steel wool
b) Al is anodic to all do not use steel wool
c) Mg is cathodic to all do not use steel wool
d) Al is cathodic to all do not use steel wool
Q.42) Unsalvageable, MTCS [ CAR-145,48]
a) Which are going to reach their certified life
b) Which have repairable defect
c) Which data cannot be retrieved
d) Which can return to airworthiness condition
Q.43) Which type of drill are used for soft and thin materials [Shop Theory,151]
a) Fluted drill
b) Twist drill
c) Straight-fluted drill
Q.44) MTCS [Module 7,5.27]
a) ATA 22 (Auto flight)
b) ATA 34 (Oxygen)
c) ATA 28 (pneumatic)
Q.45) Null field dischargers are used for [Module 7,19.2]
a) Severe turbulences
b) Lightning strike protection
c) Heavy Landings
d) None
Q.46) Burning erosion is form on [Module 7,19.2]
a) Heavy landing
b) Lighting strike
c) Severe turbulence
Q.47) Baroscopic is [Module 7,18.39]
a) Visual inspection
b) (a)+ internal only
c) (a)+ external only
Q.48) Radiography interpretation [Module 7,18.54]
a) Performed by experience personal
b) Anybody can do it
c) Performed by nonexperience personal
Q.49) Radiography inspection procedure [Module 7,18.55]
a) Film processing---->Interpretation--->Preparation & Exposure
b) Preparation & Exposure ----> Film processing ---> Interpretation
c) Interpretation ----> Preparation & Exposure ---> Film processing
Q.50) Soft hammers are made from: - [Module 7,3.11]
a) Hockery
b) Rawhide
c) Rubber
d) (a)+(b)+(c)+Leather
Q.51) Pliers used for crimping: - [Module 7,3.9]
a) Round Nose
b) Needle Nose
c) Long Nose
Q.52) Wrench that can be used for various sizes of nuts: - [Module 7,3.13]
a) Adjustable Wrench
b) Strap Wrench
c) Hex-Key
Q.53) Cape chisel is [Shop Theory,63]
a) Not as round nose chisel
b) As diamond cut chisel
c) Convex chisel
Q.54) Hacksaw strokes, MTCS: - [Module 7,3.19]
a) 50 to 60 per minute
b) 30 to 40 per minute
c) 40 to 50 per minute
Q.55) Lathe Machine: -
a) Not used for drilling
b) Only on inside of cylinder
c) Works on both inside and outside of cylinder.
d) None
Q.56) For class B fire:- [Module 7,1.9]
a) Water Type fire extinguisher
b) CO2
c) Dry Chemicals
Q.57) Blades in which only teeth is hardened is called [Module 7,3.19]
a) All hard blade
b) Flexible blade
c) Hard blade
d) None
Q.58) Parco lubrizing, MTCS [Titterton,261]
a) Limited to Al alloy only
b) Limited to Iron & steel parts
c) Limited to copper & its alloy
Q.59) Total amount of variation in size of part is [Module 7,6.3]
a) Tolerance
b) Clearance
c) Allowance
Q.60) Tolerance? 1.653+0.001-0.003 [Module 7,6.3]
a) Unilateral
b) Bilateral
c) None
Q.61) Turn buckles, MTCS [Module 6,10.5]
a) 2 threaded terminals
b) 1 threaded terminals
c) 1 threaded barrel & 2 threaded terminals
Q.62) Taper pin carries which load [Module 6,5.9]
a) Tensile load
b) Shear load
c) Both
Q.63) Flux is used in welding [Module 7,15.2]
a) To reduce the amount of solder
b) To reduce the effect of corrosion
c) To reduce the effect of oxidation
d) To reduce over heating
Q.64) Pinning of file [Shop Theory]
a) Cut more metal than required
b) Reduce efficiency
c) Increase efficiency
Q.65) Which process produce 20% stronger steel & limited to steel only [Titterton]
a) Hardening
b) Annealing
c) Normalizing
Q.66) File burrs and abrasions are removed by:- [Module 7,3.23]
a) Burnishing tool
b) Compressed air
c) File Card/Wire Brush
This paper is prepared with my best of knowledge, if any question is wrong please suggest in comment box. Thanks for your visit.
MODULE 7 MAINTENANCE PRACTICE PDF, MODULE 7 MAINTENANCE PRACTICE PAPER , MODULE 7 MAINTENANCE PRACTICE NOTES, MODULE 7 MAINTENANCE PRACTICE DOWNLOAD
easa module 7 book pdf free download, module 7 maintenance practices questions, asa module 7 essay questions and answers pdf, easa part 66 module 7 pdf, easa module 7 syllabus, module 7 question answer, module 7 books, aircraft maintenance practices, easa module 7 book pdf, easa module 7 book pdf free download, module 7 easa, dgca module 7 syllabus, module 7 question answer, module 7 notes, easa module 7 essay questions and answers pdf, dgca module books pdf easa module 7 book pdf free download, dgca module 8 question paper dgca module 1301 question paper, dgca module 6 question paper dgca module books pdf module 10 dgca question paper
